1. Peachtree Woodworking Supply
#ad
Phenolic Zero Clearance Insert for Delta Uni-Saw Contractor | Large Grizzly and Other Table Saws with a 13-3/8” x 3-3/4” x 1/2” Throat Plate Opening
#adPeachtree Woodworking Supply #ad - Also be aware of the shape of your current insert of whether its round, we recommend that you measure the exact length, square ends or if there are any indents or protruding notches. You can also use zero clearance inserts with dado blade sets. Zero clearances help minimize this situation from happening since there is no gap between the blade and the zero clearance opening.Zero clearance inserts help prevent tear out by essentially enveloping the blade on all sides which doesn’t allow the wood to tear out since there is not gap between the blade and insert. The insert features two snug Fit sand-able side tabs that allow you to remove a little material at a time for a perfect fit if necessary.
More information #ad
This is especially true when cutting plywood. This can cause that piece of wood to jam up against the blade and go flying across the room or worse yet, right back at you. Measure your factory insert and compare size before you order. The reason you would use zero clearance inserts with dado blades is to reduce the amount of tear out the dado blade set produces. Zero clearance inserts can be used in conjunction with most any table saw blade including thin kerf, standard kerf and carbide tipped blades. This zero clearance insert is made from a high density phenolic material that was chosen for its ability to stand up to everyday workshop use. Since every table saw brand and manufacturer is different, width and thickness of your table saw insert or opening and compare it to the size we list.
Brand | Peachtree Woodworking Supply #ad |
Manufacturer | Fulton #ad |
Part Number | AMZ-4133 |
Model | 4133 |
More information #ad
2. Leecraft
#ad
Leecraft DL-1U Zero Clearance Table Saw Insert for Delta Table Saw Colors may Vary
#adLeecraft #ad - Includes leveling screws, side and end adjustment screws; rear safety pin; precut blade bottom pocket for fully retracted blades and bevel cuts.Measures: 13-3/8" x 3-3/4" x 1/2" Please measure before ordering. Fits: delta: unisaw & left-tilt unisaw, 35675, jet ctas-10, 35680, 10" tilt arbor saw, 35610, bridgewood bw10ts, powermatic 63, sears craftsman 22104, 10" contractor, grizzly g1023, "Hybrid" & Left-Tilt Contractor, 35670, 22114, 22124, steel city 35605, 35685.
More information #ad
Elimantes dangerous gap around blade where thin off-cuts can get wedged. Offers superior rigidity, durability, flatness, and low friction; reduces chip-out and splintering.Brand | Leecraft #ad |
Manufacturer | Leecraft #ad |
Height | 1 Inches |
Length | 4 Inches |
Width | 13.9 Inches |
Part Number | DL-1U |
Model | DL-1U |
More information #ad
3. Bosch
#ad
Bosch TS1005 Zero Clearance Insert Assembly
#adBosch #ad - Package dimensions : 13. 7 l x 07 h x 3. 7 w inches. Use for precision cuts at 90-degrees and reduces kerf clearance to a thickness of blade. Made in Taiwan. Package weight : 03 pounds.More information #ad
Brand | Bosch #ad |
Manufacturer | Bosch #ad |
Height | 0 Inches |
Length | 0 Inches |
Weight | 0.25 Pounds |
Width | 0 Inches |
Part Number | TS1005 |
Model | TS1005 |
Warranty | 1 year manufacturer warranty, 30 day money back guarantee |
More information #ad
4. Fulton
#ad
Jet,Grizzly,Power Matic 64 Zero Clearance Insert for Table Saws
#adFulton #ad - Please check your Length x Width x Thickness of your current insert before ordering. Insert dimensions: 12-1/2” x 3-9/16” x 7/16” - jt-164 jet/Powermatic 64A Zero-Clearance Table Saw Insert.More information #ad
Made from high-density phenolic laminate with a bonded-melamine surface. Small jet, grizzly, Powermatic 64 insert will fitvarious models of table saws. Includes leveling screws, side and end adjustment screws;pre-cut blade bottom pocket.Brand | Fulton #ad |
Manufacturer | Fulton #ad |
Part Number | AMZ-4134 |
Model | AMZ-4134 |
More information #ad
5. Leecraft
#ad
Leecraft PM-1 Zero Clearance Table Saw Insert For Powermatic Model 66
#adLeecraft #ad - Reduces saw noise. Reduced chip-out and splintering. Kerf serves as handy stock alignment guide. Reduces sawdust expelled. Supports work right up to the blade.More information #ad
Brand | Leecraft #ad |
Manufacturer | Leecraft #ad |
Height | 0.5 Inches |
Length | 14.44 Inches |
Weight | 1.3 Pounds |
Width | 4 Inches |
Part Number | PM-1 |
Model | PM-1 |
More information #ad
6. Fulton
#ad
New Craftsman/Rigid Phenolic Zero Clearance Insert for Table Saws 14”x 3-3/4” x 3/16" 4131
#adFulton #ad - Made from: Phenolic Material. Please check your Length x Width x Thickness of your current insert before ordering. New craftsman / rigid insert 4131 fits various models of table saws. Purchase two inserts and get FREE SHIPPING! Insert dimensions: 14”x 3-3/4” x 3/16".More information #ad
Brand | Fulton #ad |
Manufacturer | Fulton #ad |
Part Number | AMZ-4131 |
More information #ad
7. DEWALT
#ad
DEWALT Dado Throatplate for 10-Inch Portable Table Saw DWE7402DI
#adDEWALT #ad - For woodworking and building. Package weight: 0372 kilograms. Allows for use of stacked dado cutters. Can be used with dwe7490 and DWE7491 versions.More information #ad
Brand | DEWALT #ad |
Manufacturer | Dewalt #ad |
Height | 10.19 Inches |
Length | 17.5 Inches |
Weight | 0.85 Pounds |
Width | 8.88 Inches |
Part Number | DWE7402DI |
Model | DWE7402DI |
More information #ad
8. Leecraft
#ad
Leecraft CR-3 Sears Vintage 10-Inch Belt-drive Zero Clearance Table Saw Insert
#adLeecraft #ad - Greatly reduced chip-out and splintering. Supports work right up to the blade. Elimantes dangerous gap around blade where thin off-cuts can get wedged.More information #ad
Brand | Leecraft #ad |
Manufacturer | Leecraft #ad |
Height | 1 Inches |
Length | 14 Inches |
Weight | 1.2 Pounds |
Width | 4 Inches |
Part Number | CR-3 |
Model | CR-3 |
More information #ad