Top 8 Winding Bars Garage Door – Garage Door Springs & Wires

As an Amazon Associate I earn from qualifying purchases.

1. ZhenT

#ad

Premium 2Pcs Winding Bars with Non-Slip Handle 1/2 Inch in Diameter X 18 Inch in Length,Used for Garage Door Torsion Spring

#ad
ZhenT #ad - Premium material:use heat treated 45 steel to make sure the bar won’t bend or break off during operation. Non-slip handle:compared with other products, we add knurling on handle to provide maximum control and enhance safety. Dimension: diameter 1/2" In x length 18" In, weight 1lb each. Anti-rust surface:surface is zinc plated, not tend to rust. One end colored red to make sure it is inserted to the full depth. Appliciation:used to wind or unwind the tension on torsion springs, save yourself over a $100 bill from a garage door company.
BrandZhenT #ad
ManufacturerZhenT #ad
Height0.47 Inches
Length17.4 Inches
Weight2.05 Pounds
Width1.08 Inches

2. NIDAYE

#ad

2 Pack 18 Inch Winding Rods for Torsion Springs, 0.5inch Diameter Steel Winding Bars for Adjusting or Replacing Garage Door Tension Springs with Rubber Handle

#ad
NIDAYE #ad - When adjusting or replacing garage door torsion springs, it is extremely important that these tasks are not attempted with any tools other than these rods. They are designed to industry standard for residential garage door use, fit most residential winding cones.

Must have tool: torsion spring winding rods is the only tool recommended to make torsion spring adjustments to balance the weight of a garage door. Application: the pair of torsion spring winding rods are specifically designed for increasing winding and decreasing unwinding the tension on residential garage door torsion springs. If you have any problem, please don't hesitate to contact us, we'll reply within 24 hours.

Failure to use these rods when replacing or adjusting torsion springs may result in personal injury and property damage. Safety first: steel torsion rods allow you to safely perform torsion spring replacements and adjustments without worrying about keeping the spring tension under control. Dimensions: garage door torsion spring winding rod are 047inch in outside diameter and 17. 7” long.
BrandNIDAYE #ad
ManufacturerNIDAYE #ad
Part Numberwinding rods

3. Service Spring

#ad

GDN Garage Door Winding Bars Pair Hex

#ad
Service Spring #ad - Hex and Round work the same. Either will Work Fine. Cold rolled Hardened Steel Bars. Made in USA. Hex shape keeps the bar from rolling away.
BrandService Spring #ad
ManufacturerService Spring #ad

4. Impact Spring

#ad

2Pcs Garage Door Torsion Spring Winding Bar,Galvanized Steel Winding Rod with Non-slip Handle for Adjusting or Replacing Tension Spring,0.5’’ Diameter, 18’’LengthSliver

#ad
Impact Spring #ad - Failure to use these rods when replacing or adjusting torsion springs may result in badly personal injury and property damage. Premium material:our bars are made of heat treated 45 steel and have a strong load carrying capacity, allow you to safely perform torsion spring replacements and adjustments without worrying about spring tension out of control.

Standard size:garage door torsion spring winding rod are 05’’ in outside diameter and 18’’ in length. They are designed to industry standard for residential garage door use, fit most residential winding cones. One end colored red to make sure it is inserted to the full depth. Important:torsion spring winding bar is the only tool recommended to make torsion spring adjustments to balance the weight of a garage door.

Special non-slip handle:knurled handle design, ensures that it will never slip even if your hands are sweating. Unlike rubber handle, embossed handle will not be sticky and slippery as time goes on. Application: the pair of torsion spring winding rods are specially designed for increasing winding and decreasing unwinding the tension on residential garage door torsion springs.
BrandImpact Spring #ad
ManufacturerImpact Spring #ad

5. PRIME-LINE

#ad

Prime-Line GD 52238 Torsion Spring Winding Rods – The Only Tools Recommended for Adjusting or Replacing Garage Door Tension Springs – 1/2” Diameter x 16” Long Round Steel Rods Pack of 2

#ad
PRIME-LINE #ad - They are designed to industry standard for  residential garage door use. Dimensions – garage door torsion spring winding rods are 1/2” in outside diameter and 16” long. Torsion spring rods are not for use on winding cones larger than 33/64" in diameter.

Must have tool – gd 52238 torsion spring winding rods is the only tool recommended to make torsion spring adjustments to balance the weight of a garage door. Failure to use these rods when replacing or adjusting torsion springs may result in personal injury and property damage. Winding cones usage - winding cones should be wound and unwound 1/4 turn at a time. When adjusting or replacing garage door torsion springs, it is extremely important that these tasks are not attempted with any tools other than these rods.

Safety first – steel torsion rods allow you to safely perform torsion spring replacements and adjustments without worrying about keeping the spring tension under control. Wind and unwind springs – the pair of torsion spring winding rods are specifically designed for increasing winding and decreasing unwinding the tension on residential garage door torsion springs.
BrandPRIME-LINE #ad
ManufacturerPrime-Line Products #ad
Height12.2 Inches
Length13.78 Inches
Weight1.8 Pounds
Width22.05 Inches
Part NumberGD 52238
ModelGD 52238
WarrantyAs listed.

6. Originalidad

#ad

1/2 Inches Diameter x 18 Inches Long Torsion Spring Winding Rods, Garage Door Winding Bars, Use for Adjusting or Replacing Garage Door Tension Springs

#ad
Originalidad #ad - Not suitable for winding cones larger than 33/64" in diameter. Garage door spring Winding Bars with Steel Material. Fit most residential winding cones. Use for unwinding and winding torsion springs. 1/2" round bar, about 18" length and 1. 76 lbs weight.
BrandOriginalidad #ad
ManufacturerOriginalidad #ad
Height1.18 Inches
Length5.91 Inches
Width3.15 Inches
Part NumberORD-A013

7. Magic Hub

#ad

Garage Door Torsion Spring Winding Bars 24in, Hex Winding Bars, Set of Two

#ad
Magic Hub #ad - The pair garage door torsion Spring Winding Bars 24 Inch Hex. Hex winding bars - hex shape except for the ends that go into the winding cone gives you a better grip as you are winding your torsion springs. These are professional grade winding bars. 24″ hex - 1/2″ at one end 5/8″ at the other end 24″ Long. Machine milled ends, hardened steel. Also the shape of the bars prevent the bars from rolling off the tray of your ladder and hitting you garage door as you move from one side to the other.
BrandMagic Hub #ad
ManufacturerImported #ad

8. SS

#ad

Pair of 218 X 2" X 21", 33" Garage Door Torsion Springs with Winding Bars 26

#ad
SS #ad - Springs come with a 3 year limited warranty. Includes pair of springsleft and right, nylon bushing and winding bars. Torsion springs are black coated, corrosion resistant, oil tempered and made in the U. S. A.
BrandSS #ad
ManufacturerSS #ad
Height2 Inches
Length33 Inches
Weight30 Pounds
Width2 Inches
Part NumberTS20218
ModelTS20218